Cervical Facet Dislocations: A Ventral Surgical Strategy for Decompression, Reduction, and Stabilization

Published on 02/04/2015 by admin

Filed under Neurosurgery

Last modified 02/04/2015

Print this page

This article have been viewed 2737 times

Chapter 94 Cervical Facet Dislocations

A Ventral Surgical Strategy for Decompression, Reduction, and Stabilization

R.o.n. Riesenburger, Simcha J. Weller, Sait Naderi, Edward C. Benzel

Much controversy surrounds the management of subaxial cervical subluxations resulting from facet fracture-dislocation.¹^–¹¹ An initial attempt at closed reduction using skeletal traction is not without risk.¹²^–¹⁸ The most serious complication of cervical traction and closed reduction is the retropulsion of disc fragments into the spinal canal and resultant spinal cord compression (Fig. 94-1). Several reports of neurologic deterioration after closed reduction in the setting of concurrent disc herniation have been described.¹⁹^–²³ In addition, late instability is relatively common in patients treated with closed reduction alone, because of the concomitant presence of significant ligamentous disruption associated with these injuries.

FIGURE 94-1 A typical bilateral facet dislocation with disc extrusion. A, Note that the spinal cord is compressed predominantly by the dislocated caudal vertebral body and rostral lamina before reduction. B, After reduction, the large fragment of extruded disc has been retropulsed into the spinal canal (arrow), resulting in spinal cord compression.

(From University of New Mexico, Division of Neurosurgery, with permission.)

The surgical technique for the open reduction of unstable cervical dislocations varies from surgeon to surgeon. Most reports have described dorsal reduction techniques.^20,^21,²⁴^–²⁹ However, the ventral surgical approach for reduction has its advocates.³⁰ Several small series have been published that describe the technique of ventral reduction of locked facets.^19,³¹^–³⁵ Because of the popularization of dorsal fixation techniques (e.g., lateral mass plating and spinous process wiring), ventral reduction has not been widely used in clinical practice. However, an increasing concern has been raised regarding the danger associated with the dorsal reduction of a cervical spine dislocation in the presence of a ventral disc herniation.^19,²¹^–²⁴ Furthermore, because of the common coexistence of significant dorsal bony and soft tissue disruption, a three-vertebral segment (two-motion segment) dorsal fixation is commonly required to stabilize a two-vertebral segment (one-motion segment) instability. In addition, in dorsal reduction of locked facets, it is commonly necessary to remove a significant portion of the involved facet(s), thus often mandating a three-vertebral segment dorsal fixation procedure. Conversely, ventral reduction may be followed by arthrodesis of only a single-motion segment, thus sparing additional motion segments from arthrodesis.

Kwon et al.³⁶ concluded that both ventral stabilization and dorsal stabilization for unilateral cervical facet injuries were valid treatment options. In this randomized study of 42 patients with unilateral cervical facet injuries, patients on whom a ventral approach was used had a lower rate of wound infection, had a higher rate of radiographically demonstrated union, and healed in a more lordotic sagittal alignment. However, they also more frequently had signs of dysphagia and voice changes in the early postoperative period in comparison to the group treated with dorsal stabilization. Patients undergoing a ventral approach should be informed of these (and all other) risks.

Surgical Technique

Discectomy

The standard ventromedial approach is used through a transverse skin incision. After radiographic confirmation of the operative level, a discectomy is performed. A special consideration in the case of facet dislocation is the ventral translation (ventrolisthesis) of the rostral vertebral body on its caudal counterpart. This is often associated with some degree of kyphotic angulation and a resultant obscuration of the disc space, necessitating removal of the ventral aspect of the caudal end plate of the rostral vertebral body with a high-speed air drill (Fig. 94-2). Care must be taken not to remove so much of the vertebral body as to preclude ventral screw-plate fixation. After exposure of the disc space, a standard discectomy is performed. The posterior longitudinal ligament is always removed, thus exposing the dura mater and ensuring adequate decompression.

FIGURE 94-2 The ventrocaudal aspect of the rostral vertebral body obscures visualization of the disc interspace, necessitating partial resection.

(From University of New Mexico, Division of Neurosurgery, with permission.)

Reduction

After completion of the discectomy, deformity reduction is attempted. Often, simple distraction is successful, because a potentially significant obstruction to reduction (the disc and anulus fibrosus) has been removed. However, if this maneuver fails, one of two intraoperative maneuvers may be used to facilitate reduction through the ventral approach: the interbody spreader technique or the vertebral body post technique. Failure to use either technique appropriately may result in failure of reduction.

Interbody Spreader Technique

A Cloward interbody spreader, or an equivalent device, is inserted into the disc interspace at a 30- to 40-degree angle (Fig. 94-3A). Failure to place this device at an angle results in achieving only distraction force application (as simple distraction with tongs achieves). This does not result in the application of a bending moment, which is required for reduction with this technique.

FIGURE 94-3 The interbody spreader technique for reduction of locked facets. After completion of discectomy, the spreader is placed into the disc interspace at a 30- to 40-degree angle. A, Note that the blades of the spreader should be placed deep enough to provide an adequate bending moment. B, The application of traction (thick arrow) and the simultaneous opening of the appropriately placed spreader (thin arrows) create a bending moment and distraction of the disc interspace. C, The application of a dorsally directed force by the spreader on the ventrocaudal aspect of the rostral vertebral body results in the realignment of the disengaged vertebrae.

(From University of New Mexico, Division of Neurosurgery, with permission.)

While distraction is gradually applied with the disc interspace spreader (applied in the midvertebral body region) (Fig. 94-3B), the spreader is rotated rostrally. This applies a bending moment to the dislocated vertebral body while the facet dislocation is reduced by distraction. If the locked facets are disengaged, the vertebrae should realign. Distraction is then relaxed in the aligned position, and the spreader is removed (Fig. 94-3C).

For bilateral facet dislocations, the intervertebral spreader should be placed in the midvertebral body region. For unilateral dislocations, the spreader should be placed on the side of the dislocation to facilitate the application of a torque about the long axis of the spine via the spreader. Placement of the intervertebral spreader too far ventrally may result in fracture of the end plate.